本文圖片及文字來源于上海淞江減震器集團網站http://www.jiuhu.cc/如有任何疑問請聯系周工021-60547771
上海淞江減震器集團是國內第一批制造管道減振設備的廠家，主要生產橡膠接頭、可曲撓橡膠接頭、阻尼彈簧減振器、橡膠隔震器、金屬和非金屬補償器、管道伸縮器等管道減振給排水設備。技術創新是淞江集團多年來孜孜不倦的追求，也正是淞江產品深受市場一致好評的根本原因。
導致異徑橡膠接頭爆裂的原因比較多，可以一一排查。首先確定管路的壓力是否過大，一般情況橡膠采用1.0MPa壓力的橡膠接頭最大壓力在2.0MPa范圍的，可以保證不爆裂，但如果壓力過大的話應該選用更高壓力的球體(1.6MPa)，1.6MPa的試壓范圍在3.0MPa。所以安裝時應安裝設計人員的要求，安裝相應壓力的橡膠接頭。
其次是采用劣質的橡膠材質生產加工的橡膠接頭;橡膠接頭安裝在戶外應防止高溫、臭氧油及酸堿環境，嚴禁暴嗮、雨淋、風濁。遇到這種情況應該好的橡膠材質，如：氯丁橡膠、三元乙丙橡膠、硅橡膠、氟橡膠等配方，采用好的橡膠可加長橡膠的使用時間，但橡膠天生懼怕曬、淋、風，用在室外或向陽迎風的管道應搭建遮陽架。
再者的原因?qū)儆诩夹g(shù)問題;橡膠接頭在硫化成型時最重要也是最關鍵的問題要看接口處的硫化，大多數橡膠接頭出先爆裂都是接口處，因為接口的工藝比較復雜繁瑣，所以容易出現問題。
Causes the different diameter rubber joint to burst the reason to be quite many, may one one investigation. First determine the pipeline pressure is too big, general situation of rubber by rubber pressure 1.0MPa joint maximum pressure in the range of 2.0MPa, can guarantee does not burst, but if the pressure is too large should choose more high pressure sphere (1.6Mpa), the 1.6Mpa pressure in the range of 3.0 MPa. Therefore, the installation should be installed in the design requirements, the installation of the corresponding pressure of the rubber joint.
Followed by the use of inferior rubber material production and processing of rubber joints; rubber connector is installed in the outdoor should prevent heat, ozone oil and acid and alkali environment, non violent Sai, rain, wind dampness. Encounter this kind of situation should be a good rubber material, such as chloroprene rubber, ternary ethylene propylene rubber, silicone rubber, fluorine rubber formula, the rubber can lengthen the using time of rubber, but rubber born afraid of sun, air shower,, in outdoor or sunny wind pipe should build the sunshade frame.
Moreover the reason is a technical problem; rubber joint is the most important in the vulcanization molding is one of the most critical problems to sulfide interface, most of the rubber joint first burst is interface, because interface technology is relatively complicated, so prone to problems.
