湖南長沙奈歐6ES7331-7TF01-0AB0西門子現貨銷售-工控行業信息網(chinagkong.com)-工控行業門戶網站

Article number	6ES7331-7TF01-0AB0
	SM331, 8AI, 0/4-20MA HART
Supply voltage
Load voltage L+
● Rated value (DC)	24 V
● Reverse polarity protection	Yes
Input current
from load voltage L+ (without load), max.	20 mA
from backplane bus 5 V DC, max.	120 mA
Output voltage
Power supply to the transmitters
● present	Yes
● Rated value (DC)	24 V
● short-circuit proof	Yes
● Supply current, max.	60 mA
Power loss
Power loss, typ.	1.5 W
Analog bs
Number of analog bs	8
permissible b current for current b (destruction limit), max.	40 mA
Input ranges (rated values), currents
● 0 to 20 mA	Yes
● Input resistance (0 to 20 mA)	140 ?
● Input resistance (-20 mA to +20 mA)	140 ?
● Input resistance (4 mA to 20 mA)	140 ?
Cable length
● shielded, max.	800 m
Analog value generation for the bs
Measurement principle	Sigma Delta
Integration and conversion time/resolution per channel
● Resolution with overrange (bit including sign), max.	16 bit
● Integration time, beterizable	Yes
● Integration time (ms)	20 ms at 50 Hz; 16.6 ms at 60 Hz; 100 ms at 100 Hz
● Basic conversion time, including integration time (ms)	55 ms @ 60 Hz, 65 ms @ 50 Hz, 305 ms @ 100 Hz
● Interference voltage suppression for interference frequency f1 in Hz	10 / 50 / 60 Hz
Smoothing of measured values
● beterizable	Yes
● Step: None	Yes
● Step: low	Yes
● Step: Medium	Yes
● Step: High	Yes
Encoder
Connection of signal encoders
● for current measurement as 2-wire transducer	Yes
● for current measurement as 4-wire transducer	Yes
Errors/accuracies
Linearity error (relative to b range), (+/-)	0.01 %
Temperature error (relative to b range), (+/-)	0.001 %/K
Crosstalk between the bs, min.	70 dB
Repeat accuracy in steady state at 25 °C (relative to b range), (+/-)	0.1 %
Operational error limit in overall temperature range
● Current, relative to b range, (+/-)	0.15 %
Basic error limit (operational limit at 25 °C)
● Current, relative to b range, (+/-)	0.1 %
Interference voltage suppression for f = n x (f1 +/- 1 %), f1 = interference frequency
● Series mode interference (peak value of interference < rated value of b range), min.	40 dB
● Common mode interference, min.	100 dB
Isochronous mode
Isochronous operation (application synchronized up to terminal)	No
Interrupts/diagnostics/status inbation
Diagnostic functions	Yes
Alarms
● Diagnostic alarm	Yes
● Limit value alarm	Yes
Diagnostic messages
● Diagnostic inbation readable	Yes
Diagnostics indication LED
● Group error SF (red)	Yes
● Channel fault indicator F (red)	Yes
Potential separation
Potential separation analog bs
● between the channels	No
● between the channels and backplane bus	Yes
Isolation
Isolation tested with	500 V DC
Degree and class of protection
IP degree of protection	IP20
Connection b
required front connector	20-pin
Dimensions
Width	40 mm
Height	125 mm
Depth	117 mm
Weights
Weight, approx.	205 g

在StartDrive項目里，如果變頻器的參數設置已經通過USB接口上傳，那么這個變頻器/或控制單元的序列號就會被保存在StertDrive項目里。

對于已有的StartDrive項目，如何通過USB接口在線變頻器呢？

要使用已有的StartDrive項目在線一臺同型號的新變頻器，必須將新變頻器的相關序列號添加到項目中，并保存。

設置過程如下

選擇一個新設備

在項目樹里面打開驅動。
雙擊“Online & diagnostics”并打開。
選擇“Online access”。
最近一次是通過USB接口上傳時，接口設置會自動保存。在"Online access"下的“Type of the PG/PC interface”中選擇“S7USB”，在“PG/PC interface”中選擇“USB”。
舊變頻器的序列號會顯示在設備地址里（本示例為：XAC503-002064）。
點擊“Select Device”按鈕添加新變頻器的相關序列號。